ET 200L

	6ES7 131-1BH01-0XB0	6ES7 131-1BL01-0XB0
Supply voltages
Rated value
24 V DC	Yes	Yes
Reverse polarity protection	Yes	Yes
Hardware configuration
Rack
Required terminal block	TB 16L	TB 32L
Connection method
Inputs/outputs	Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection	Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection
PROFIBUS DP
Transmission rate, max.	1.5 Mbit/s	1.5 Mbit/s
Direct data exchange (slave-to-slave communication)	Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)	Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)
Digital inputs
Number of digital inputs	16	32
Input voltage
Rated value, DC	24 V	24 V
for signal "0"	-30 to +5 V	-30 to +5 V
for signal "1"	13 to 30 V	13 to 30 V
Input current
for signal "1", typ.	5 mA	5 mA
Input delay (for rated value of input voltage)
for standard inputs
at "0" to "1", min.	2 ms	2 ms
at "0" to "1", max.	4.5 ms	4.5 ms
Cable length
Cable length for NAMUR input, shielded, max.	1 000 m	1 000 m
Galvanic isolation
between PROFIBUS DP and all other circuit components	Yes	Yes
Galvanic isolation digital inputs
between the channels	No	No
between the channels and PROFIBUS DP	Yes	Yes
Environmental requirements
Operating temperature
horizontal installation, min.	0 °C	0 °C
horizontal installation, max.	60 °C; 40°C for other mountings	60 °C; 40°C for other mountings
Air pressure
permissible range, min.	795 hPa	795 hPa
permissible range, max.	1 080 hPa	1 080 hPa
Relative humidity
Operation, min.	5 %	5 %
Operation, max.	95 %; RH class 2 in accordance with IEC 1131-2	95 %; RH class 2 in accordance with IEC 1131-2
Vibrations
Operation, checked according to IEC 60068-2-6	Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)	Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)
Shock test
checked according to IEC 60068-2-27	Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms	Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms
Degree of protection
IP20	Yes	Yes
Dimensions and weight
Dimensions
Width	145 mm	145 mm
Height	60 mm	60 mm
Depth	60.5 mm	60.5 mm

	6ES7 132-1BH00-0XB0	6ES7 132-1BL00-0XB0
Supply voltages
Rated value
24 V DC	Yes	Yes
Reverse polarity protection	Yes	Yes
Mains buffering, min.	20 ms	20 ms
Load voltage 2L+
Rated value (DC)	24 V; 1L+, 2L+, 3L+	24 V; 1L+, 2L+, 3L+
Current consumption
from load voltage L1 (without load), max.	50 mA; per load group (L1+ or L2+ / L3+)	100 mA; per load group (L1+ or L2+ / L3+)
from supply voltage L+, max.	70 mA; L4+ / L5+	70 mA; L4+ / L5+
Power losses
Power loss, typ.	5 W	7 W
Hardware configuration
Rack
Required terminal block	TB 16L	TB 32L
Communication functions
Bus protocol/transmission protocol	PROFIBUS DP	PROFIBUS DP
Connection method
Inputs/outputs	Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection	Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection
PROFIBUS DP
Transmission rate, max.	1.5 Mbit/s	1.5 Mbit/s
SYNC capability	Yes	Yes
Direct data exchange (slave-to-slave communication)	Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)	Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)
Digital outputs
Number of digital outputs	16	32
Short-circuit protection	Yes; Electronic	Yes; Electronic
Response threshold, typ.	0.7 A	0.7 A
Limitation of inductive shutdown voltage to	typ. (L1+ or L2+ / L3+) -55 V	typ. (L1+ or L2+ / L3+) -55 V
Lamp load, max.	5 W	5 W
Controlling a digital input	Yes	Yes
Output voltage
Rated value (DC)	24 V	24 V
for signal "1", min.	Ua - 3 V	Ua - 3 V
Output current
for signal "1" rated value	0.5 A	0.5 A
for signal "1" permissible range for 0 to 60 °C, max.	0.5 A	0.5 A
for signal "0" residual current, max.	1 mA	1 mA
Output delay with resistive load
0 to "1", max.	50 ms	50 ms
1 to "0", max.	200 ms	200 ms
Parallel switching of 2 outputs
for increased power	No	No
for redundant control of a load	Yes; only outputs of the same group	Yes; only outputs of the same group
Switching frequency
with resistive load, max.	100 Hz	100 Hz
with inductive load, max.	0.5 Hz	0.5 Hz
on lamp load, max.	8 Hz	8 Hz
Aggregate current of outputs (per group)
all other mounting positions
up to 40 °C, max.	2 A	2 A
up to 60 °C, max.	4 A	4 A
horizontal arrangement, up to 40 °C, max.	3 000 mA	3 000 mA
horizontal arrangement, up to 60 °C, max.	2 000 mA	2 000 mA
Load resistance range
lower limit	41 Ω	41 Ω
upper limit	28 000 Ω	28 000 Ω
Cable length
Cable length, shielded, max.	1 000 m	1 000 m
Cable length unshielded, max.	600 m	600 m
Interrupts/diagnostics/status information
Alarms
Alarms	No	No
Diagnoses
Diagnostic functions	Yes	Yes
Diagnostics indication LED
Bus fault BF (red)	Yes	Yes
Status indicator digital output (green)	Yes	Yes
Status indicator digital input (green)	Yes	Yes
Monitoring 24 V voltage supply ON (green)	Yes	Yes
Isolation
Isolation checked with	500 VDC	500 VDC
Galvanic isolation
between PROFIBUS DP and all other circuit components	Yes	Yes
Galvanic isolation digital outputs
between the channels	No	No
between the channels and PROFIBUS DP	Yes; Optocoupler	Yes
Environmental requirements
Operating temperature
horizontal installation, min.	0 °C	0 °C
horizontal installation, max.	60 °C; 40°C for other mountings	60 °C; 40°C for other mountings
Air pressure
permissible range, min.	795 hPa	795 hPa
permissible range, max.	1 080 hPa	1 080 hPa
Relative humidity
Operation, min.	5 %	5 %
Operation, max.	95 %; RH class 2 in accordance with IEC 1131-2	95 %; RH class 2 in accordance with IEC 1131-2
Vibrations
Operation, checked according to IEC 60068-2-6	Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)	Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)
Shock test
checked according to IEC 60068-2-27	Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms	Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms
Degree of protection
IP20	Yes	Yes
General information
Vendor identification (VendorID)	0016h	0011h
Dimensions and weight
Dimensions
Width	145 mm	145 mm
Height	60 mm	60 mm
Depth	60.5 mm	60.5 mm
Weight
Weight, approx.	130 g	150 g

	6ES7 133-1BL01-0XB0
Supply voltages
Rated value
24 V DC	Yes
Reverse polarity protection	Yes
Hardware configuration
Rack
Required terminal block	TB 32L
Connection method
Inputs/outputs	Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection
PROFIBUS DP
Transmission rate, max.	1.5 Mbit/s
Direct data exchange (slave-to-slave communication)	Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)
Digital inputs
Number of digital inputs	16
Input voltage
Rated value, DC	24 V
for signal "0"	-30 to +5 V
for signal "1"	13 to 30 V
Input current
for signal "1", typ.	5 mA
Input delay (for rated value of input voltage)
for standard inputs
at "0" to "1", min.	2 ms
at "0" to "1", max.	4.5 ms
Cable length
Cable length for NAMUR input, shielded, max.	1 000 m
Digital outputs
Number of digital outputs	16
Short-circuit protection	Yes; Electronic
Output voltage
Rated value (DC)	24 V
for signal "1", min.	Ua - 3 V
Output current
for signal "1" permissible range for 0 to 60 °C, max.	0.5 mA
for signal "0" residual current, max.	1 mA
Switching frequency
with resistive load, max.	100 Hz
with inductive load, max.	0.5 Hz
on lamp load, max.	8 Hz
Aggregate current of outputs (per group)
up to 60 °C, max.	4 A
Cable length
Cable length, shielded, max.	1 000 m
Galvanic isolation
between PROFIBUS DP and all other circuit components	Yes
Galvanic isolation digital inputs
between the channels	No
between the channels and PROFIBUS DP	Yes
Environmental requirements
Operating temperature
horizontal installation, min.	0 °C
horizontal installation, max.	60 °C; 40°C for other mountings
Air pressure
permissible range, min.	795 hPa
permissible range, max.	1 080 hPa
Relative humidity
Operation, min.	5 %
Operation, max.	95 %; RH class 2 in accordance with IEC 1131-2
Vibrations
Operation, checked according to IEC 60068-2-6	Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)
Shock test
checked according to IEC 60068-2-27	Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms
Degree of protection
IP20	Yes
Dimensions and weight
Dimensions
Width	145 mm
Height	60 mm
Depth	60.5 mm

	6ES7 193-1CH00-0XA0	6ES7 193-1CH10-0XA0	6ES7 193-1CH20-0XA0	6ES7 193-1CL00-0XA0	6ES7 193-1CL10-0XA0
Dimensions and weight
Dimensions
Width	145 mm	145 mm	191 mm	191 mm	191 mm
Height	100 mm; Height with electronics block from top edge of DIN rail (with bus connector 6ES7 972-0CA30-0XA0): 82 mm	100 mm; Height with electronics block from top edge of DIN rail (with bus connector 6ES7 972-0CA30-0XA0): 82 mm	100 mm; Height with electronics block from top edge (with bus connector ): 98.5 mm	100 mm; Height with electronics block from top edge of DIN rail (with bus connector 6ES7 972-0CA30-0XA0): 82 mm	100 mm; Height with electronics block from top edge of DIN rail (with bus connector 6ES7 972-0CA30-0XA0): 82 mm
Depth	40.5 mm	40.5 mm	40.5 mm	40.5 mm	40.5 mm
Weight
Weight, approx.	230 g	230 g	283 g	350 g	350 g